1-10V controller for universal dimmer switches, 1 NO contact 600VA

État de l’article	Nouveau
Nom du fabricant	1-10V controller for universal dimmer switches, 1 NO contact 600VA
Marque	ELTAKO
Catégories	Interrupteurs
Pays d’origine	CN
Code du système harmonisé	8536 5080 00
Disposition de l'assemblage	Autre
Mode de fonctionnement	Bouton de commande tactile
Type de charge	Charge capacitive
Largeur de l'appareil	18 mm
Hauteur de l'appareil	58 mm
Profondeur de l'appareil	66 mm

Niveau d’emballage 1	4010312108116, 4010312108116
Niveau d’emballage 2	4010312108116
Niveau d’emballage 3	4010312108116

Méthode de montage	DRA (adaptateur pour rail DIN)
Couleur	Bleu
Sans halogène	Yes
Type de connexion	Borne vissée
Protection de surface	Autre
Qualité des matériaux	Thermoplastique
Matériau	Plastique
Type de fixation	Autre
Mémoire de la valeur lumineuse	No
Entrée de la sous-station	No
Variateur en série	No
Applicable avec un capteur de mouvement	No
Applicable avec bouton de transmission	No
Applicable avec bouton infrarouge	No
Applicable avec indicateur de présence	No
Applicable avec bouton	Yes
Applicable avec minuterie/interrupteur	No
Tension de contrôle	8-230 V
Transparent	No
Finition de la surface	Mat
Section du noyau	6 mm²
Prise en charge IFTTT disponible	No
Coupure de la phase de gradation	No
Phase de coupure de la gradation	No
Contrôle par application via Bluetooth	No
Compatible avec Apple HomeKit	No
Compatible avec Google Assistant	No
Compatible avec Amazon Alexa	No

1 NO contact potential free 600VA and 1-10V control output 40mA. Standby loss 0.9 watt only. Modular device for DIN-EN 60715 TH35 rail mounting. 1 module = 18mm wide, 58mm deep. State-of-the-art hybrid technology combines advantages of nonwearing electronic control with high capacity of special relays. The controller SUD12 can be used in two different modes: Mode 1-10V output: In this mode electronic ballast units and transformers with a 1-10V interface up to a total control current of 40mA can be controlled when connected to an universal dimmer switch EUD12D or MFZ12PMD. The EUD12D or the MFZ12PMD is controlled with pushbuttons at the universal control voltage input locally or centrally. The SUD12 converts the dimmer signals from Y1/Y2 to the 1-10V output 0/Q1 for the interface. It switches the electronic ballast with a bistable relay at the output EVG (electronic ballast units). Zero passage switching to protect contacts. The switching capacity for ­fluorescent lamps or low voltage halogen lamps with electronic ballast is up to 600VA. By using a bistable relay coil power loss and heating is avoided even in the on mode. The switched load may not be connected to the mains before the short automatic synchronisation after installation has terminated. At the same time a dircectly dimmable lamp can be connected to the dimmer switch EUD12D. Furthermore the dimmer switch EUD12D or MFZ12PMD can be expanded with capacity enhancers LUD12 for directly dimmable lamp. Mode 1-10V input: In this mode the output of a 1-10V controller can be converted at A1/0 into a direct dimming function when ­connected to a capacity enhancer LUD12 at terminals X1/X2. The closing operation and the opening operation is also carried out externally at L of the SUD12. The rotary switch of the LUD12 must be adjusted to the setting two lamps (additional lamps). Further capacity enhancers LUD12 in the mode increase of capacity with additional lamps can be connected to the controller SUD12. A 100K potentiometer for brightness control may also be directly connected to the control input A1/0. If the input A1/0 is disconnected the LUD12 dimms to maximum brightness.