Multifunction universal dimmer switch, Power MOSFET up to 400W

État de l’article	Nouveau
Nom du fabricant	Multifunction universal dimmer switch, Power MOSFET up to 400W
Marque	ELTAKO
Catégories	Interrupteurs
Pays d’origine	CN
Code du système harmonisé	8536 5080 00
Disposition de l'assemblage	Autre
Mode de fonctionnement	Bouton de commande tactile
Type de charge	Universelle
Tension nominale	230 V
Largeur de l'appareil	45 mm
Hauteur de l'appareil	45 mm
Profondeur de l'appareil	18 mm
Puissance de commutation max.	400 W

Niveau d’emballage 1	4010312107973, 4010312107973
Niveau d’emballage 2	4010312107973
Niveau d’emballage 3	4010312107973

Méthode de montage	Montage encastré (plâtre)
Couleur	Bleu
Sans halogène	Yes
Type de connexion	Borne vissée
Protection de surface	Autre
Qualité des matériaux	Thermoplastique
Matériau	Plastique
Type de fixation	Montage avec vis
Mémoire de la valeur lumineuse	Yes
Entrée de la sous-station	No
Variateur en série	No
Applicable avec un capteur de mouvement	No
Applicable avec bouton de transmission	No
Applicable avec bouton infrarouge	No
Applicable avec indicateur de présence	No
Applicable avec bouton	Yes
Applicable avec minuterie/interrupteur	No
Tension de contrôle	8-230 V
Transparent	No
Finition de la surface	Mat
Section du noyau	4 mm²
Prise en charge IFTTT disponible	No
Coupure de la phase de gradation	No
Phase de coupure de la gradation	No
Profondeur minimale de la boîte d'encastrement	18 mm
Contrôle par application via Bluetooth	No
Puissance nominale charge résistive	400 W
Puissance nominale charge inductive	400 VA
Puissance nominale charge capacitive	400 VA
Compatible avec Apple HomeKit	No
Compatible avec Google Assistant	No
Compatible avec Amazon Alexa	No

Universal dimmer switch. Power MOSFET up to 400W. Automatic lamp ­detection. Standby loss 0.1 watt only. With adjustable minimum brightness. With switching operation for children's rooms and snooze function. Built-in device for installation. 45mm long, 45mm wide, 18mm deep. Universal dimmer switch for lamps up to 400W, depending on ventilation conditions, dimmable 230V LED lamps and dimmable energy saving lamps (ESL) are also dependent on the lamp electronics. Zero passage switching with soft start and soft OFF to protect lamps. Universal control voltage input 8 to 230V UC, electrically isolated from the 230V supply voltage and switching voltage. Short-time control commands switch on/off, permanent control varies the brightness to the maximum level. A interruption of control changes the direction of dimming. The brightness level is stored after switching off in case the function memory is set. If the function on max is set, it always switches on at the maximum brightness level. In case of a power failure the switching position and the brightness level are stored. If applicable the dimmer will be switched on at the stored brightness level after the supply voltage is recovered. Automatic electronic overload protection and over-temperature switch-off. The minimum brightness level (completely dimmed down) can be adjusted with the upper rotary switch %lamp, e.g. for dimmable energy saving lamps. You can dim all lamp types in automatic mode. Use the lower function rotary switch to select between five automatic mode functions: memory, memory+soft on, on max, on max+soft on and ESV+soft on. +ESL is a convenience setting for energy saving lamps which must be switched on at high voltage for design reasons so that they can also be switched back on cold in dimmed state. -ESL is a convenience setting for energy saving lamps which cannot be switched back on in dimmed state for design reasons. This is why memory is switched off in this position. No inductive (wound) transformers may be used in +ESL and -ESL settings. In addition the maximum number of dimmable energy saving lamps may be lower than in automatic mode for design reasons. Setting of function ESV same as memory+soft on with setting of a release delay up to 90 minutes with the rotary switch %lamp if the manual off command is not given. Before time-out switch-off early warning function by dimming down within 1 minute. Switching operation for children's rooms: If the light is switched on by holding down the pushbutton, it starts at the lowest brightness level after approx. 1 second and dims up slowly as long as the pushbutton is held down without modifying the last stored brightness level. Snooze function: With a double impulse the lighting is dimmed down from the current dimming position to the minimum brightness level and switched off. The current dimming position as well as the adjustable minimum brightness level determine the dimming time (max. = 60 minutes) which can be reduced as required. It can be switched off at any time by short-time control commands during the lighting is dimmed down. Holding down the pushbutton during the dimming down process dims up and stops the snooze function. Mixing of L loads (inductive loads, e.g. wound transformers) and C loads (capacitive loads, e.g. electronic transformers) is not permitted. R loads (ohmic loads, e.g. 230V incandescent lamps and halogen lamps) may be added anytime.