Multifunction universal dimmer switch, Power MOSFET up to 400W

État de l’article	Nouveau
Nom du fabricant	Multifunction universal dimmer switch, Power MOSFET up to 400W
Marque	ELTAKO
Catégories	Interrupteurs
Pays d’origine	CN
Code du système harmonisé	8536 5080 00
Disposition de l'assemblage	Autre
Mode de fonctionnement	Bouton tournant
Fréquence	50 Hz
Type de charge	Universelle
Tension nominale	230 V
Largeur de l'appareil	18 mm
Hauteur de l'appareil	58 mm
Profondeur de l'appareil	66 mm
Puissance de commutation max.	400 W

Niveau d’emballage 1	4010312109489, 4010312109489
Niveau d’emballage 2	4010312109489
Niveau d’emballage 3	4010312109489

Méthode de montage	DRA (adaptateur pour rail DIN)
Couleur	Bleu
Sans halogène	Yes
Type de connexion	Borne vissée
Protection de surface	Autre
Qualité des matériaux	Thermoplastique
Matériau	Plastique
Type de fixation	Autre
Mémoire de la valeur lumineuse	Yes
Entrée de la sous-station	No
Variateur en série	No
Applicable avec un capteur de mouvement	No
Applicable avec bouton de transmission	No
Applicable avec bouton infrarouge	No
Applicable avec indicateur de présence	No
Applicable avec bouton	Yes
Applicable avec minuterie/interrupteur	No
Tension de contrôle	8-230 V
Transparent	No
Finition de la surface	Mat
Section du noyau	6 mm²
Prise en charge IFTTT disponible	No
Coupure de la phase de gradation	Yes
Phase de coupure de la gradation	Yes
Contrôle par application via Bluetooth	No
Puissance nominale charge résistive	400 W
Puissance nominale charge inductive	400 VA
Puissance nominale charge capacitive	400 VA
Compatible avec Apple HomeKit	No
Compatible avec Google Assistant	No
Compatible avec Amazon Alexa	No

Universal dimmer switch. Power MOSFET up to 400W. Automatic lamp detection. Standby loss 0.3 watt only. With adjustable minimum brightness, maximum brightness and dimming speed. With switching operation for children's rooms and snooze function. Modular device for DIN EN 60715 TH35 rail mounting. 1 module = 18mm wide, 58mm deep. Universal dimmer switch for lamps up to 400W, depending on ventilation conditions, dimmable 230V LED lamps and dimmable energy saving lamps (ESL) are also dependent on the lamp electronics and the dimming technology. Up to 3600W with capacity enhancers LUD12-230V at the terminals X1 and X2. Universal control voltage 8 to 230V UC and additionally the universal voltage control inputs 8 to 230V UC central ON and central OFF. The control inputs are electrically isolated from the supply voltage and switching voltage. Zero passage switching with soft start and soft OFF to protect lamps. In case of a power failure the switching position and the brightness level are stored. If applicable the dimmer will be switched on at the stored brightness level after the supply voltage is recovered. From 110V control voltage glow lamp current up to 5mA (not for DSD). Automatic electronic overload protection and over-temperature switch-off. The functions and times are entered using the MODE and SET keys as described in the operating manual and indicated on the LC display. A keylock function is provided. You can dim all lamp types in automatic mode settings EUD, DSD, Udo, STS, MIN, MMX, CG and R. EUD = Universal dimmer switch with settings for dimming speed, minimum brightness, maximum brightness, memory and Soft ON/OFF as well as choice of priority for central control. ESL and LED is settable. Short-time control commands switch on/off, permanent control varies the brightness to the maximum level. A interruption of control changes the direction of dimming. LED is a convenience setting for dimmable 230V LED lamps which cannot be dimmed down far enough in automatic mode (phase cut-off) for design reasons and must therefore be forced to phase control. There is a choice of 3 dimming curves. ESL is a convenience setting for energy saving lamps which must be switched on at high voltage for design reasons so that they can also be switched back on cold in dimmed state. Memory must be switched off on energy saving lamps which cannot be switched back on in dimmed state for design reasons. No inductive (wound) transformers may be used in ESL and LED settings. In addition the maximum number of lamps may be lower than in automatic mode for design reasons. Switching operation for children's rooms: If the light is switched on by holding down the pushbutton, it starts at the lowest brightness level after approx. 1 second and dims up slowly as long as the pushbutton is held down without modifying the last stored brightness level. Snooze function: With a double impulse the lighting is dimmed down from the current dimming position to the minimum brightness level and switched off. The current dimming position as well as the adjustable minimum brightness level determine the dimming time (max. = 60 minutes) which can be reduced as required. It can be switched off at any time by short-time control commands during the lighting is dimmed down. Holding down the pushbutton during the dimming down process dims up and stops the snooze function. DSD = Same as universal dimmer switch EUD but also comprising activation via two direction switches on the universal voltage control inputs 8..230V UC. Udo = Same as universal dimmer switch EUD but also comprising setting for a time delay from 1 to 99 minutes. Switch-off early warning at the end by dimming is selectable and adjustable from 1 to 3 minutes. STS = Staircase time switch with switchable switch-off early warning by dimming. With pump and permanent light by pushbutton. Time adjustable from 1 to 99 minutes. Switch-off early warning (no flickering) by dimming is adjustable from 1 to 3 minutes. Also for dimmable energy saving lamps ESL and 230V LED lamps. MIN = Universal dimmer switch, switches when control voltage is applied to the minimum brightness setting. Maximum brightness is dimmed during the set dim time from 1 to 99 minutes. When the control voltage is interrupted, the device is switched off immediately, even during the dim time. MMX = Same function as for MIN, when the control voltage is interrupted, dimming still continues until the set minimum brightness is reached. Then the device is switched off. CG = Clock with adjustable switch on/off times from 0.1 to 9.9 seconds. The maximum brightness is adjustable from 3 to 99%. R = Switching relay with setting for Soft ON/OFF from 0.1 to 9.9 seconds. The maximum brightness is adjustable from 3 to 99%. ON = permanent ON. OFF = permanent OFF. The dim position in % or the time lapse in minutes is indicated in the middle of the display. The expired, resettable switch-on time is indicated at the bottom of the display. Display menu guidance including language selection (German, English, French, Italian or Spanish) is described in the supplied operating instructions.